Close Sidebar
Available at Zen RC.
Arriving this week.
Heligods - The International RC Helicopter Forum
Learn to Fly 3d RC Helicopters
Now the DEVS at Accurc had told me there were some big changes re helis about to be released. Well I have been ignoring this sim for a while because it started to fall behind the other sims. BUT check out the new release details!!
Improvements:
Fixes:
Improvements:
- Interlink transmitter modes added
- Interlink and Vbar switch handling improved
- Camera settings can now be changed in flight mode
- Mouse over help text for icons
Fixes:
- Nitro sounds not playing correctly
- Installer crash on some systems
- Start up failure on Windows 10
- MP3 player fixes...
Upcoming Event
[Nov 22, 2015] 2015 Victorian F3C Helicopter State Championships (Karramomus, Victoria)
2015 Victorian F3C Helicopter State Championships
20th to 22nd November at the Ian Watts Field, 935 Karramomus Rd, Karramomus, Victoria (just out of Shepparton)
Classes:Sportsman, Advanced, Expert and F3C
Entry is $30 and open to all MAAA registered / FAI affiliated pilots, to register follow the link below.
2015 Victorian F3C Helicopter State Championships Online Registration
Competition Rules:...
20th to 22nd November at the Ian Watts Field, 935 Karramomus Rd, Karramomus, Victoria (just out of Shepparton)
Classes:Sportsman, Advanced, Expert and F3C
Entry is $30 and open to all MAAA registered / FAI affiliated pilots, to register follow the link below.
2015 Victorian F3C Helicopter State Championships Online Registration
Competition Rules:...
I am transferring my O.S. GT15HZ gas engine to another airframe, and noticed that, the ignition module metal braid wire to the spark plug is worn in a few parts.
Does anyone know where to buy some metal braid wire to patch it up?
I dont care about aesthetics, its the RF shielding that I am worried about. Would it be enough to go to a hardware shop, and get some metal braiding of a plumbing hose fitting?
I am guessing for EMI shielding, copper metal would be best. Maybe some copper tape from Altronics or Jaycar?
Does anyone know where to buy some metal braid wire to patch it up?
I dont care about aesthetics, its the RF shielding that I am worried about. Would it be enough to go to a hardware shop, and get some metal braiding of a plumbing hose fitting?
I am guessing for EMI shielding, copper metal would be best. Maybe some copper tape from Altronics or Jaycar?
Well every once and a while new stuff comes along and you think that it cant improve on current technology. Such is the case I thought with HALO blades until I grabbed a pair of switch blades from @ZENRC for my Goblin 380 on the weekend. I was lucky enough to give them a blast today.
Let me state I have been using HALO 385s which are also fantastic blade as well. I will en-devour to explain the differences.
GEOMETRY:
The SWITCH blades are 2mm shorter but the taper is much shallower at the tip - ie the switches are a bit...
Let me state I have been using HALO 385s which are also fantastic blade as well. I will en-devour to explain the differences.
GEOMETRY:
The SWITCH blades are 2mm shorter but the taper is much shallower at the tip - ie the switches are a bit...
Vendor Notice - ZenRC
Kse 570 Now Available
Available at Zen RC.
Arriving this week.
Vendor Notice - Mad4heli
Xpert Servo
Question?
A Tacky Subject.......
I am almost finished repairing a crashed heli,all that is left is the 2 boom struts,which are a carbon material,but the "grip" that they slide into,and then screwed to a boom clip is plastic,a few suggestions as to a glue that dont setup instantly,and WONT melt (chemical reaction)plastic............?
Notice
Castle Crap Governor
Hi there
After 26 flights with my 700L dominator (castle 160 hv / 850mx) I have to say that Im not satisfied with the governor of the esc. From instable rpms to gear chattering and back.. Means that I have tried several tuning options and didnt get stable rpm - I have always a slight tail blowout (nose left) on all rpm, low mid and high.
The tail torque precompensation of my beastx is wothless anyway. That option just doesnt work. Tried that allready on my 500 and now on the big one.
Seems that I have to run the 700 with the good old throttle curve. Getting a VBar with governer or...
After 26 flights with my 700L dominator (castle 160 hv / 850mx) I have to say that Im not satisfied with the governor of the esc. From instable rpms to gear chattering and back.. Means that I have tried several tuning options and didnt get stable rpm - I have always a slight tail blowout (nose left) on all rpm, low mid and high.
The tail torque precompensation of my beastx is wothless anyway. That option just doesnt work. Tried that allready on my 500 and now on the big one.
Seems that I have to run the 700 with the good old throttle curve. Getting a VBar with governer or...
Page 495 of 773
New Posts
Loading...
XenPorta 2 PRO
© Jason Axelrod from 8WAYRUN.COM
test
