Cgy750 More Positive Pitch Than Negative

Discussion in 'Futaba CGY750 FBL System' started by Stuart, Nov 14, 2014.

By Stuart on Nov 14, 2014 at 9:30 AM
  1. Stuart

    Stuart Active Member

    Joined:
    May 10, 2014
    Messages:
    405
    Likes Received:
    214
    Just gone through the setup using the new sokoh heli tool app.
    All yery good. My issue is that the CGY750 only has a percentage pit check setting that is applied to both positive and negative pitch.

    I was after 11deg pitch. I get that on positive. Negative however comes up short with 9.8deg.

    How do I correct this?

    Stuart
    Citizen #507
     

Comments

Discussion in 'Futaba CGY750 FBL System' started by Stuart, Nov 14, 2014.

    1. Fredo

      Fredo Well-Known Member

      Joined:
      Mar 19, 2014
      Messages:
      190
      Likes Received:
      273
      What would happen if you altered the endpoint in the TX pitch channel ? On some FBL systems you have to get the FBL unit to recognise 100% input from the TX.
       
    2. smakmeharder

      smakmeharder Administrator

      Joined:
      Mar 3, 2014
      Messages:
      4,825
      Likes Received:
      3,096
      Under the swash basic menu are all servos centered at the NTR adjustment? IE the centers have not shifted due to your alignment?
       
    3. Manyc

      Manyc Well-Known Member

      Joined:
      Mar 14, 2014
      Messages:
      1,619
      Likes Received:
      1,189
      you can also adjust this mechanically.. but I just change the endpoints in the radio...
       
    4. Stuart

      Stuart Active Member

      Joined:
      May 10, 2014
      Messages:
      405
      Likes Received:
      214
      Thanks guys... I think I will do both a mechanical and CGY reset and start again. If I end up in the same place I'll do a end point adjustment...

      So if the ball links to the DFC head are tightened all the way in, then my only mechanical adjustment us the servo arm to swash rods. I assume to decrease positive and increase negative I wind these in a turn or two?
       
    5. Stuart

      Stuart Active Member

      Joined:
      May 10, 2014
      Messages:
      405
      Likes Received:
      214
      @smakmeharder you raise a good point. I think I did this setup with my old setup already in the unit. Point being I used the soko heli tool app with the .NTR settings from my pre crash config so it probably means my starting position for the soko app was out by my previous .NTR adjustments.

      Will try over the weekend with.a zero starting point for each servo and see what happens.
       
    6. Manyc

      Manyc Well-Known Member

      Joined:
      Mar 14, 2014
      Messages:
      1,619
      Likes Received:
      1,189
      I think you just drop the entire swash down
       
      • Like Like x 1
      • Agree Agree x 1
      • List
    7. R12NDS

      R12NDS New Member

      Joined:
      Nov 11, 2014
      Messages:
      4
      Likes Received:
      5
      I was watching a great video for setting up the Align 3GX by Freddie Can Fly and he covered this very point.

      The swash plate needs to be raised or lowered by the three links from the servos.

      Can't remember which way as mine were already in the perfect place.

      Good luck and hope that helps.
       
    8. Stuart

      Stuart Active Member

      Joined:
      May 10, 2014
      Messages:
      405
      Likes Received:
      214
      Thanks I had already made that conclusion. It was a couple of turns on each link and all was good.
      Freddy makes some very informative videos, he is a great contributor to our hobby.


      Stuart
      Citizen #507
       

Share This Page

test

    About Us

    Just like you, Heligods staff are regular everyday fliers. Join our forum and participate in what will become the worlds greatest rc helicopter forum..

    Credits:

    A big thank you to the following people who helped us put together this site:

    Pope Francis

    Deli Lama

    George Bush

    Gene Simmons (aka Crash)